Page 48 of 99

Re: Geoff's 3AJ rebuilds....

Posted: Thu Feb 02, 2012 8:48 pm
by scottieh
Geoff or Mezo, can you explain the starter motor cable trick? I've never really looked inside a starter motor and this seems to be a good one you guys use over and over, so I'd like to know a little about it. Thanks.

[quote="GeoffD"]Ye olde cable tie trick.... :wink2:

Image

Re: Geoff's 3AJ rebuilds....

Posted: Thu Feb 02, 2012 11:42 pm
by Mezo
Ye Olde Cable tie trick came about when i did my starter, i was struggling to hold all four brushes back while i inserted the armature up through inside, unless you have a whole bunch of people helping you?

Image

Just push the brushes back & hold them with small (mini ties) and the armature slides up inside, one man job.

Image

If you look carefully you will see the cable ties right at the top of the brushes, this is to allow part of the armature to move in to position & once it gets a bite you can snip away the ties & push it fully in to place.

The yellow arrow is just pointing out not to get that wire trapped (short circuit).

Mezo.

Re: Geoff's 3AJ rebuilds....

Posted: Fri Feb 03, 2012 12:04 am
by Paulba
Hi Mezo,

Is that the edge where the arrow is pointing that you had to clean of paint to get the starter working again?

Paul

Re: Geoff's 3AJ rebuilds....

Posted: Fri Feb 03, 2012 12:23 am
by Mezo
Paulba wrote:Hi Mezo,

Is that the edge where the arrow is pointing that you had to clean of paint to get the starter working again?

Paul
Yep around that lip i had to much paint, and i did the same on the other end just in case.

Mezo.

Re: Geoff's 3AJ rebuilds....

Posted: Fri Feb 03, 2012 12:32 pm
by GeoffD
+1 what Mezo said...another tip, don't put the cable ties around the brushes too tight, so when you enter the armature it'll push the ties off ....


Fitted mine this morning...

Image

Image

Re: Geoff's 3AJ rebuilds....

Posted: Mon Feb 06, 2012 4:49 pm
by scottieh
Mez, Geoff, thanks for the starter tip. Although I was working on a DR650 starter, the trick worked a treat and I got the brushes back in no problem. With information and tips like this I'll be working on the Tenere like I actually know what I am doing! Thanks to the forum and thanks to its members! :star:

Re: Geoff's 3AJ rebuilds....

Posted: Wed Feb 08, 2012 4:18 pm
by GeoffD
Off to the powder coater's again....... Tenere 4 ( :eekers: ) frame, Tenere 3 rear carrier & brake pedal, Super Ten swinging arm & spring


Image

Re: Geoff's 3AJ rebuilds....

Posted: Thu Feb 09, 2012 9:59 pm
by GeoffD
Got myself a couple of bargains for Tenere 4...

A swinging arm, complete with all bolts, pins, bearings, etc..... £15
This went off for powder coating this arvo...

Image

Bargain of the Month, a 3AJ inner rear mudguard in mint condition...,,, .89p

Image

Re: Geoff's 3AJ rebuilds....

Posted: Thu Feb 09, 2012 11:06 pm
by Mezo
Half the fun is chasing the parts in this game, and when you score a bargain it feels good eh Geoff. :biggrin:

89p :lol:

Mezo.

Re: Geoff's 3AJ rebuilds....

Posted: Fri Feb 10, 2012 8:22 pm
by GeoffD
Got the carbs fitted this morning chaps..... :funkynanna:


Image